MS60BKR
Fits TVs 32”- 60”
flat panel solutions
Fixed Wall Mount for LCD, Plasma,
and LED Displays
Maximum Load
Capacity – 130 lb (60kg)
Instruction Manual
Specifications
Display Size:
Maximum Load:
Mounting Pattern:
Profile:
32” to 60”
130 lb (60kg)
600 mm x 400 mm (23.6” x 15.7”) max
1.2” (3.0 cm)
Box contents
Wall Plate (x1)
Mount Arm (x2)
Safety Rod (x1)
Instruction Manual (x1)
Hardware Kit (x1)
Template (x1)
Warnings
1. Read these instructions before you begin. If
you are unsure of any part of the process, contact
a professional contractor or installer for assistance.
Improper installation can result in injury or damage.
CAUTION:
This wall mount is intended for use only with the
maximum weight of 60 kg (130 lbs). Use with heavier
than the maximum weights indicated may result in
instability causing possible injury.
2. The wall or mounting surface must be capable of
supporting the combined weight of the mount and
the display; if not, the structure must be reinforced.
3. Locate pipes, wires, or any other hazards in the wall
where you wish to install the mount before drilling.
4. Safety gear and proper tools must be used. Failure
to do so can result in injury or damage.
5. Two people are recommended for installation.
Do not attempt to lift a heavy display without
assistance.
6. Follow all instructions and recommendations
regarding adequate ventilation and suitable
locations for mounting your display. Consult the
owner‘s manual for your particular display for more
information.
Pour des instructions
en français, se
reporter à la page 5.
Para obtener
instrucciones en
español, consulte la
página 9.
Continues on next page...
Part 1B – Mounting to the Wall (Concrete)
IMPORTANT! For safety reasons, the concrete wall must be capable of
supporting the combined weight of the mount and the display. The manufacturer
takes no responsibility for failure caused by walls of insufficient strength.
1. Place the mounting template against the wall in the desired location. Make sure
the template is level.
Fig.3
2. Drill two 10 mm (3/8”) holes in the wall using the template as a guide. Remove
any excess dust from the holes (see Fig. 3).
3. Remove the template from the wall and insert a concrete anchor (C) into each
hole so that it is flush with the concrete surface. A hammer can be used to
lightly tap the anchors into place if necessary.
NOTE: If the concrete wall is covered by a layer of plaster or drywall, the
concrete anchor must pass completely through the layer to rest flush with the
concrete surface.
Fig.4
4. Place the wall plate against the wall over the inserted anchors and attach it
using the lag bolts (A) and lag bolt washers (B) provided (see Fig. 4). Do not
over-tighten these bolts and do not release the wall plate until both
bolts are in place. Ensure that the wall plate remains level after both bolts are secured.
Part 2 – Attaching the Mount Arms to the Display
IMPORTANT! Use extra care during this part of the installation. If possible, avoid placing your display facedown
as it may damage the viewing surface.
NOTE: This mount comes with a selection of different screw diameters and lengths to accommodate a wide variety
of display models. Not all of the hardware in the kit will be used. If you cannot find the appropriate screw size in the
kit provided, consult the manufacturer of your display for more information.
1. Determine the correct length of screw to use by examining the back of your display:
A. If the back of your display is flat and the mounting holes are flush with the surface, you will use the shorter
screws (D, F, or H) from the hardware kit.
B. If the back of your display is curved, has a protrusion, or if the mounting holes are recessed, you will need
to use the longer screws (E, G, or I) and may also need to use the spacers (K).
2. Determine the correct diameter of screw to use by carefully trying one of each size (M4, M6 and M8) from the
hardware kit. Do not force any of the screws – if you feel resistance stop immediately and try a smaller
diameter screw.
3. Attach the mount arms to the back of your display using the screws identified in Steps 1 and 2 (see Fig. 5):
For displays
with flat
backs.
For displays
with curved
or recessed
backs.
Fig.5
A. If you are using the M4 or M6 screws you will also need to use the M6 washers (J). M8 screws do not
require washers.
B. If you are using the longer screws on a display with a curved or recessed back, you may also need to use
the spacers (K). Use one spacer or two spacers stacked as needed. Only use a spacer if necessary.
Continues on next page...
3
Part 3 – Final Assembly
1. With the help of another person, carefully lift your display and place it on the wall plate. Do not release the
display until the mount arms have securely hooked onto the wall plate.
2. Insert the safety rod through the wall plate to prevent the display from being lifted from the wall plate. A padlock
can be inserted into the end of the rod to help prevent theft of your display (see Fig. 6).
Safety Rod
Padlock (optional,
not included)
Fig.6
IMPORTANT! The safety rod should be used at all times to prevent the display from being accidentally
knocked from the mount.
3. Periodically clean your mount with a dry cloth. Inspect all screws and hardware at regular intervals to ensure
that no connections have become loose over time. Re-tighten as needed.
4
|